Microwave-assisted combustion synthesis of ZnAl2O4 and ZnO nanostructure particles for photocatalytic wastewater treatment

ZnAl₂O₄ and ZnO nanostructure particles and in situ crystallization of zinc aluminate and zinc oxide coating layers on sintered α-Al₂O₃ and γ-Al₂O₃ granules by the microwave-assisted combustion method were investigated. For powders, the effects of solution pH value and for coated samples the influence of support type on the structure, microstructure, and photocatalytic activity of powders were studied. Results showed that variation of synthesis pH value caused to considerable change in agglomeration, specific surface area, obtaining up to 88 and 92% yields for zinc aluminate and zinc oxide nanoparticles, respectively. γ-alumina granules were more appropriate supports than the α-alumina ones because of the better photocatalytic activities and lower extent of the attritions for both zinc aluminate and zinc oxide coating layers.     

Failure mechanism of MCrAlY coating at the coating‐substrate interface under type I hot corrosion

MCrAlY coatings are widely used to provide protection of hot component in modern gas turbine engines against high‐temperature oxidation and hot corrosion. Coating‐substrate interface, where the substrate is only partially covered by the ?coatings, is vulnerable to the hot corrosion attack. The accelerated degradation at the coating‐substrate interface can cause fast spallation of the coating, leading to the early failure of the gas turbine components. In this paper, MCrAlY powder was deposited on IN792 disks by high‐velocity oxygen‐fuel spraying. The hot corrosion behavior of the coated sample was investigated using (0.8Na, 0.2K)₂SO ₄ salt deposition at 900°C in lab air. Results showed a minor attack in the coating center, however, an accelerated corrosion attack at the coating‐substrate interface. The fast growth of corrosion products from substrate caused large local volume expansions at the coating‐substrate interface, resulting in an early coating spallation.     

Simulating the effect of aluminizing on a CoNiCrAlY-coated Ni-base superalloy

MCrAlY (M = Ni, Co) coatings are commonly used on gas-turbine components as oxidation resistant overlay coatings and bondcoats for thermal barrier systems. The present work focuses on the effect of the aluminizing process on the CoNiCrAlY coating microstructure. In the as-received condition the outer part of the coating consisted mostly of β-(Ni,Co)Al with interspersed precipitates of Cr-rich carbide and Cr-rich boride precipitates. Formation of σ-CoCr was observed at the interface between the β-layer and the inner initial CoNiCrAlY microstructure. Scanning electron microscopy (SEM) combined with energy and wavelength-dispersive X-ray spectroscopy (EDX/WDX) was employed to characterize the aluminized CoNiCrAlY coating. Phases were then identified by electron backscatter diffraction (EBSD). Detailed microstructural studies of the coating were corroborated with the help of coupled thermodynamic-kinetic calculations to model the aluminizing process. The calculations were performed with the in-house developed code employing the commercially available thermodynamic and kinetic databases (ThermoCalc). The mechanisms of the observed microstructural changes were elucidated with the help of the modelling results.     

Selective Coating of SnS on the Bio‐Inspired Moth‐Eye Patterned PEDOT:PSS Polymer Films

A new strategy for the selective coating of tin sulfide (SnS) on the surface of moth‐eye patterned (MEP) conducting polymer film is studied by considering the optical properties of the antireflective moth‐eye pattern and flexibility of polymer films. The semiconductor SnS is selectively coated on the surface of MEP microdomes of poly(3,4‐ethylenedioxythiophene) poly(styrene‐sulfonate) (PEDOT:PSS) film. The SnS coated MEP film is obtained by using pore selectively SnS thin layer functionalized polystyrene honeycomb‐patterned porous (HCP) film as a template. Aqueous PEDOT:PSS solution is poured on the SnS functionalized HCP films and detached for the fabrication of SnS coated MEP films. The films show a satisfactory photo‐responsive property under solar stimulated light illumination due to the antireflective MEP structure of PEDOT film and homogenous SnS coating on the surface of the conducting polymer.     

氟橡胶包覆硝酸肼镍及其对雷管撞击感度的影响

利用水悬浮法将氟橡胶包覆在硝酸肼镍(NHN)表面制备出了NHN造型粉,并将其应用于基础雷管。通过DSC研究了NHN造型粉的热性能，测试了NHN造型粉的机械感度和火焰感度以及工业基础雷管的撞击感度和起爆能力。研究结果表明:氟橡胶包覆能够提高NHN的热稳定性，且热稳定性随着氟橡胶包覆量的增加而提高；NHN造型粉的机械感度均低于原料NHN，当氟橡胶包覆量（质量分数）为9%时，撞击感度下降幅度明显，可达142.9%；NHN造型粉用在基础雷管中做起爆药，可以降低基础雷管的撞击感度并保持其起爆能力。     

热处理对等离子喷涂铁基非晶合金涂层微观结构和耐腐蚀性能的影响

采用等离子喷涂技术在Q235钢基体上制备Fe48Cr15Mo14C15B6Y2非晶合金涂层,之后对涂层进行200,300,500,600,700℃热处理,研究了热处理对涂层微观结构、耐电化学腐蚀性能和耐均匀腐蚀性能的影响。结果表明:随着热处理温度的升高,涂层的非晶含量降低,孔隙率先减小后增大,经300℃热处理后涂层的孔隙率最低,且低于未热处理涂层的;热处理后涂层中的晶体相主要包括α-Fe,Fe-Cr,Fe63Mo37,Fe3C等;随着热处理温度的升高,涂层的自腐蚀电流密度先减小后增大,经300℃热处理后,自腐蚀电流密度最小,涂层的耐电化学腐蚀性能最好;经过热处理后,涂层在NaCl溶液中浸泡31d后的单位面积质量损失减小,且热处理温度越高,单位面积质量损失越小,涂层的耐均匀腐蚀性能提高。     

Use of nets treated with food-grade coatings on dry-cured ham to control Tyrophagus putrescentiae infestations without impacting sensory properties

Dry-cured hams may become infested with the ham mite Tyrophagus putrescentiae during aging. Food-grade coatings have been developed to control mite infestations as a potential alternative to replace methyl bromide, but dipping or spraying these coatings requires additional labor and processing steps. Nets composed of polyester, a polyester/cotton blend and cotton were infused with coatings that consisted of propylene glycol, and either propylene glycol alginate and carrageenan or xanthan gum. Results indicated that the polyester/cotton blend and cotton nets that contained propylene glycol were effective at controlling mite infestations in assays with ham cubes covered in nets. The polyester nets slowed mite growth but were not effective at controlling mite reproduction due to low absorbance of the coatings. Polyester/cotton blend nets treated with coatings on whole hams were not different from control hams with respect to flavor, texture and moistness. Mite infestation tests on whole hams indicated that coated nets with greater stitch densities were effective at controlling mite growth. Future research will include the optimization of coating formulations and scaled-up testing in dry-cured ham plants.     

Ultrathin hydroxyapatite coating on pure magnesium substrate prepared by pulsed electron ablation technique

Magnesium (Mg) as a potential material for biodegradable implants is attractive due to its mechanical similarity to the bone tissue and nontoxic corrosion products. However, the rapid corrosion rate of bare magnesium is associated with hydrogen release, which may complicate the healing process. The corrosion rate may be reduced by suitable alloying, but concurrently the biocompatibility of such alloy might be deteriorated. Another way of reduction of the corrosion rate is coating. Hydroxyapatite (HA)-based coating is considered to improve biocompatibility as well as decrease the corrosion rate by the barrier effect. In this study, ultrathin (150 nm) HA and HA containing Sr coatings are deposited via pulsed electron ablation technique on pure Mg. The microstructure of the coating was assessed by scanning electron microscopy. Electrochemical methods were used to investigate the corrosion properties of prepared coatings. The materials covered by this layer were characterized by superior corrosion behavior, with corrosion rates of coated samples up to five times lower as compared with the uncoated ones. Such coating is the thinnest coating found in the literature sources.